ダポール
ジアリルフタレート樹脂成形材料 Diallyl Phthalate Molding Compounds
| 試験項目 Test items |
単位 Units |
試験法 Test method |
D500 | D2500F | D2200F | ||
| 絶縁破壊の強さ Dielectric breakdown strength |
常態 at ordinary state |
MV/m | JIS K6911 | 12-16 | 12-14 | 12-16 | 12-14 |
| 浸漬後 after immersion in water |
12-16 | ― | ― | ― | |||
| 絶縁抵抗 Insulation resistance |
常態 at ordinary state |
MΩ | JIS K6911 | 10 8 -10 9 | 10 14 -10 15 | 10 8 -10 9 | 10 8 -10 9 |
| 煮沸後 after boiling |
10 7 -10 8 | 10 13 -10 14 | 10 7 -10 9 | 10 7 -10 8 | |||
| 長期湿中電気抵抗 Insulation resistance after moisture treatment for long time |
体積 volume |
MΩ | JIS K6918 | 10 3 -10 4 | ― | ― | ― |
| 表面 surface |
10 2 -10 4 | ― | ― | ― | |||
| 誘電率(1MHz) Dielectric constant |
常態 at ordinary state |
― | JIS K6911 | 4.4-4.6 | ― | 4.3-4.6 | 4.3-4.6 |
| 浸漬後 after immersion in water |
4.4-4.7 | ― | ― | ― | |||
| 誘電正接(1MHz) Dissipation factor |
常態 at ordinary state |
― | JIS K6911 | 0.012-0.015 | ― | 0.012-0.015 | 0.010-0.015 |
| 浸漬後 after immersion in water |
0.012-0.017 | ― | ― | ― | |||
| 耐アーク性 Arc resistance |
sec. | JIS K6911 | 120< | ― | 130< | 160< | |
| 耐トラッキング性 Tracking resistance |
CTI(V) | IEC Publ.112 | 500< | 600< | 500< | 500< | |
| 曲げ強さ Flexural strength |
射出成形 Injection molding |
MPa | JIS K6911 | 98-147 | 160-170 | 78-147 | 127-147 |
| 圧縮成形 Compression molding |
69-98 | ― | 69-98 | ― | |||
| シャルピー衝撃強さ Charpy impact strength |
射出成形 Injection molding |
kJ/m 2 | JIS K6911 | 3.4-5.4 | 7.3-8.0 | 3.4-5.4 | 3.9-5.9 |
| 圧縮成形 Compression molding |
2.9-4.9 | ― | 2.9-4.9 | ― | |||
| 成形収縮率 Molding shrinkage |
射出成形 Injection molding |
% | JIS K6911 | 0.50-0.80 | 0.60-0.70 | 0.60-0.80 | 0.40-0.60 |
| 圧縮成形 Compression molding |
0.40-0.70 | ― | 0.40-0.60 | ― | |||
| 高温寸法変化率 Rate of shrinkage on heating |
% | JIS K6918 | 0.05-0.10 | ― | 0.05-0.10 | 0.05-0.10 | |
| 煮沸吸水率 Boiling water absorption |
% | JIS K6911 | 0.15-0.25 | 0.18 | 0.10-0.20 | 0.10-0.15 | |
| 比重 Specific gravity |
― | JIS K6911 | 1.60-1.70 | 1.91 | 1.80-1.90 | 1.85-1.90 | |
| 加熱後の外観 Appearance after heating |
℃・2h | JIS K6911 | 180 | 210 | 180 | 280 | |
| 荷重たわみ温度 Deflection temperature under load |
℃ | JIS K6911 | 170-180 | ― | 160-180 | 280-300 | |
| 耐燃性(厚さmm) Flammability |
― | UL 94 | HB (1.02) |
V-0 (0.31) |
V-0 (1.02) |
V-0 (0.50) |
|
| 成形方法 Molding method |
射出 ・ 移送 ・ 圧縮 Injection, Transfer, Compression |
射出 ・移送 Injection, Transfer |
|||||
| その他の特性と特徴 other properties |
カサバリ 係数 Bulk factor 2.3 |
||||||
| 用途の例 | ガバナー プラグキャップ コネクター コイルボビン 端子板 自動車 鉄道 ・航空機 船舶用部品 |
スイッチ リレー コイルボビン サーモスタットケース ヒューズケース |
コンミテータ ガバナー 各種スイッチ リレーベース コネクター 通信機部品 |
SMTボビン | |||